• HOME
  • ABOUT
  • BLOG
  • CONTACT
  • FEATURES
  • PARTIES I LINK TO

Nannycraft4u

Make your handmade dreams a reality - Just ask Nanny!

  • CHARITY PROJECTS
  • TUTORIALS
    • BAGS,POUCHES,ROLLS,WALLETS
    • EMBROIDERY
    • HOME/DECOR
    • LET’S SEW
    • QUILTING TUTORIALS
    • SPIN THE PINS
    • TOYS
    • WOTZA WEDNESDAY
  • SEWING/QUILTING
    • SIMPLE PROJECTS
    • TIPS & TOOLS
  • RECIPES
  • NANNY CHAT
  • NANNY & POPPY PROJECTS
    • CRAFT ROOM
    • HOUSE
    • TRAVEL
Home » Let’s Sew Part 11 – Sewing Room Project 4 – Zippered pouch

Let’s Sew Part 11 – Sewing Room Project 4 – Zippered pouch

November 10, 2012 by Nanny 2 Comments

Print Friendly, PDF & Email

 Today we are going to sew a zipper.  These seem to cause a lot of people grief but really they are not that hard – trust Nanny!  We will use a zip to complete a Sewing Room Pouch which you can use to hold your rotary cutter or any number of sewing items.  I have made this to fit my Kai rotary cutter and a replacement blade.  You might like to vary the length to suit your needs. 
 

Let’s sew!
Today we will be using the following:
 
 
2 x rectangles of outer fabric 9″x 4.5″
1 x rectangle of lining fabric  9″x 4.5″
3 x rectangles of lining fabric 3.5″x 4.5″
1 x square 3″x3″
1 zip x 10″
some small scraps about 2″ square x 4
2 x rectangles of iron on pellon 8.5″x 4″ (you will note in the photos that I left mine the same size as the rectangle ie 9″ x 4.5″ but it will make it easier for you to turn if you trim the 1/4″ off all round)
 
You will notice that my outer fabric rectangles are made up of strips of my fabrics. You can use a whole piece of fabric 9″x 4.5″ or make it up like I did.  I used 1.5″ strips, 9″ long.  Stitch, press.
Place the stripped piece, right side up, on top of the bubbly side of the pellon – you will have 1/4″ space around the edge of the pellon.
 
 
Attach the Stitch in the Ditch Foot and, by aligning the blade with the ‘ditch’ and shifting the needle so that it falls into the ‘ditch,’stitch along the length of each strip. 
(You will hear quilters speak of ‘stitch in the ditch’ and this is what they mean – stitching(quilting) through the layers of the quilt and ‘concealing’ the stitching in the ditch that is formed by pressing a seam to the side.)
 
 
We are going to use a different Foot now  – the Rolled Hem Foot
 
Take the square and along one edge, fold over 1-2mm and press with your fingers, then fold over again just at the end.
 
With the Rolled Hem Foot attached, put the hem under the foot and lower the needle.
 
 
Sew a few stitches and leave your needle inserted in the fabric.  Lift the Pressure Foot and ease the folded hem into the curl on the foot.  Lower the foot and continue sewing while holding the fabric edge to keep it feeding evenly.
 
You will end up with a nice, even hem with a row of stitching down the middle.
 
 
Ok, you can put that foot away now and have a play with it next time you want a very small hem!!
Put your General Purpose Foot or your 1/4″ foot on….
Take the square and place it right side up, onto a 3.5″ lining rectangle and line up the bottom.
 
Place another lining rectangle on top of that and stitch down one side. Press it open.
 
 
Take the final lining rectangle and repeat the process down the other side. Press it open.
 
Take your rule and with your rotary cutter, trim the rectangle so that it is 9’x4.5″ ( you will see that the ‘pocket’ lies between 3″ and 6″ on my rule.  So that the pocket stayed centred, I then trimmed both ends)
 
 
 
Now it’s time for the zip!  Take the zip and trim the ends to the metal markers.
Take 2 pieces of your scrap and with right sides facing, put one piece either side of the zip at each end.  I am adding this to the end of the zip so that the seam formed as we join the pouch  together, doesn’t open directly into the end of the zip. (You have probably had a seam come open at the end of a zip in a skirt…)
 
Notice on the left, that I have pinned each side of the zip to hold it together – I will leave those pins there as I sew. The seams will be 7.5″ apart.  Sew down each side going across the zip.  Do this carefully- I did it twice each end because this seam will take the’ spreading of the zip open’ force as you use the pouch.  Press them open.
 
 
Trim the scrap pieces
 
 
 
The zip is now 9″ long!!  Notice how nicely the zip closes too.  Well done!
Take one of the main fabric rectangles and place it right side up. Place the zip opening from the left, right side down on top of it. Then place the pocket rectangle, right side down on top of that. Notice that the top of the pocket is facing the zip!
With the ends and side edges meeting, pin along the length of the zip.  Just check that it looks like this:
 
 
 
 
and when you flip it open:
 
We now need to attach the Zipper Foot:  
 
 
You will notice that this foot has 2 sides to it and 2 attaching bars – so you decide which side you wish to sew down and attach the foot accordingly.
This is a zipper foot from my very first machine – just to show you a different style!
 
As with attaching any foot, always turn the needle down to check if you need to shift the needle!!
Ok – with your foot attached so that you sew to the left and needle adjusted, stitch the length of the zip.  I ran the edge of the foot along the edge of the fabric .
 
 
Open it out and with your Stitch in the Ditch Foot, your stitch length to about 3 and the seam allowance facing to the main fabric, sew down the length of the zip through the main fabric and seam allowance only. This gives a nice finish and prevents it rolling and jamming the zip.
 
 
  
Now to the other side!  Place the other main rectangle right side up, then the zip with the opening now on the right, and then the other lining rectangle and repeat the process.
 
 
 
 As you are top stitching you will come to the zip slider. If you leave your needle down,  lift the foot and rotate the whole thing, you will be able to move the slider past the needle.
 Rotate the fabric back and continue stitching to the end.
 
 
 
 The outside will now look like this:
 
Before we start the next step OPEN the zip!!
Take the 2 main fabric sides and place them facing each other and this will also mean the other lining sides are facing each other. 
 
 
 Pin and stitch around the outside, remembering to leave an opening to turn the pouch through to the right side.  (I left below the pocket open)
 
 
 
 
Clip the corners and trim away the bulk at the seams and turn through to the right side.  Push the corners out with a blunt instrument, stitch the gap closed using ladder stitch or machine stitch it, tuck the lining into the pouch and TaaDaaa – you’ve done it!!
Pop your spare blade in the pocket and the cutter in the pouch and zip it up!!  
 
Well done!!  I hope you enjoyed the journey!!
Until next time
Nanny xx

Please share:

  • Click to share on Facebook (Opens in new window)
  • Click to email a link to a friend (Opens in new window)
  • Click to share on Twitter (Opens in new window)
  • Click to share on Pinterest (Opens in new window)

Related

Filed Under: BAGS,POUCHES,ROLLS,WALLETS, LET'S SEW, SEWING/QUILTING, SIMPLE PROJECTS, TUTORIALS

Comments

  1. Pam @Threading My Way says

    November 5, 2014 at 3:40 am

    A fabulous tutorial, Margie. Great idea to have the separate pocket for the blade.

    Reply
    • Nanny@nannynotes2u says

      November 5, 2014 at 10:49 pm

      Thanks Pam! It is really handy and I can’t believe I hadn’t made myself one before! 🙂

      Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

CommentLuv badgeShow more posts

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Welcome!

Welcome! I am Nanny and this is where I like to share my crafting as well as other snippets of our life in Australia. Read more

Social

Follow me on:

Like a Newsletter?

My Button4u

grab button for Nannycraft4u
<div class="nannycraft4u-button" style="width: 150px; margin: 0 auto;"> <a href="http://www.nannycraft4u.com.au" rel="nofollow"> <img src="http://i1168.photobucket.com/albums/r482/Nannycraft4u/logo8-001.jpg" alt="Nannycraft4u" width="150" height="150" /> </a> </div>

Looking for something?

Australian Women Bloggers Directory by Blog Chicks

Subscribe to Blog via Email

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Follow on Facebook

Follow on Facebook

Favourites

  • Spin The Pins - Microwave Bowl Holder
    Spin The Pins - Microwave Bowl Holder
  • Let's Sew Part 2 - Threading Your Machine
    Let's Sew Part 2 - Threading Your Machine
Follow on Instagram

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

© Nannycraft4u

All content and images belong to Nannycraft4u unless otherwise indicated. You are welcome to link back to my blog, but you may not copy whole posts, tutorials or photos without my permission. Please give credit for my work and link back to the original post at Nannycraft4u.com If you use one of my ideas, I would love to know about it. Designs and tutorials are for personal use only.

Copyright © 2023 · Lifestyle Pro Theme on Genesis Framework · WordPress · Log in